78 Ferm
CIRCULAR SAW TABLE
TECHNICAL SPECIFICATIONS
CONTENTS OF THE PACKAGE
1 Circular saw table
1 Saw blade
1 Push stick
1 Rip fence
1 Instructions
1 Safety instructions
1 Warranty card
Check the machine and accessories for transport
damage.
PRODUCT INFORMATION
Fig. 1
1. Work table
2. Guard
3. Push stick
4. Saw blade
5. Riving knife
6. Insert plate (plastic)
7. On/Off switch
8. Motor
9. Mains cable
10. Underframe
11. Rip fence
12. Locking button
13. Protractor gauge
14. Bolt for guard
15. Nut for guard
SAFETY INSTRUCTIONS
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine.
Make sure that you know how the machine functions and
how to operate it. Maintain the machine in accordance
with the instructions to make sure it functions properly.
Keep this manual and the enclosed documentation with
the machine.
ELECTRICAL SAFETY
Attention! When electrical tools are used the
following safety measures must be observed against
the danger of electric shock, injury and/or fire. Read
and pay close attention to these recommendations
before using a machine.
Always check that your mains voltage is the same
as the value on the type plate.
When replacing cords or plugs
Throw away cords or plugs as soon as they are replaced
by new ones. It is dangerous to insert the plug of a loose
cord into the wall socket.
When using extension cords
Only use an approved extension cord that is suitable for
the power consumed by the machine. The cores must
have a cross-section of at least 1.5 mm
2
. If the extension
cord is on a reel, unroll the cord completely.
When using electrical machines, always observe
local safety regulations so as to prevent fire danger,
danger of electric shocks and personal injury. It is
therefore important to read not only the following
instructions, but also the safety regulations set out
in the enclosed safety leaflet.
Keep the instructions in a safe place!
SPECIFIC SAFETY REGULATIONS
•A circular saw table must be adequately and
effectively illuminated. If fluorescent lighting is used,
the “stroboscope” effect must be taken into account.
This can make a rotating saw blade look as though it is
stationary. This can be solved by using double fittings
and creating a phase shift between the two
fluorescent tubes.
• Check the following:
• Does the connection voltage of the motor and any
protective circuit switch match the mains voltage?
(Machines designed for a mains voltage of 230V can
safely be connected to a mains voltage of 220V).
• Are the mains cord and the mains plug in good
condition? (Sturdy, not frayed and undamaged).
Voltage | 230 V~
Frequency | 50 Hz
Power consumption | 1000 W
| S3 40% 10 min
Unloaded speed | 2950 rpm
Saw blade dimensions | 205x2.7x16 mm
Max. saw capacity 90º | 43 mm
Dust extractor diameter | 31 mm
Mitre setting | 0-45°
Weight | 14 kg
Lpa (sound pressure) | 85 dB(A)
Lwa (sound power level) | 105 dB(A)
Ferm 3
SPARE PARTS LIST FBS-205/1000
REF NR DESCRIPTION FERM NR
407680 RULER 001
407557 SQUARE NUT 002
407455 KNOB 003
407555 MOVABLE QUARD 004 - 008
407681 SUNK SCREW M3 X 12 009
407560 TABLE INSERT 010
407558 RIVING KNIFE 014 - 018
407682 HANDLE LOCK SCREW 022
407683 NUT M12 023
407553 FIXING GUARD 024
407552 OUTER FLANGE 027
407551 INNER FLANGE 030
407684 STAND BAR 034
407559 SWITCH 036
407763 MOTOR 1000 WATT 038
Bli med i samtalen om dette produktet
Her kan du dele hva du synes om FERM TSM1005 Bordsag. Hvis du har et spørsmål, les først bruksanvisningen nøye. Be om en bruksanvisning kan gjøres ved å bruke vårt kontaktskjema.