Home > Gjør-det-selv > Kompressorer > FERM Kompressorer > FERM CRM1005 FC-710 Kompressor

Bruksanvisning FERM CRM1005 FC-710 Kompressor

Trenger du en bruksanvisning for FERM CRM1005 FC-710 Kompressor? Nedenfor kan du se og laste ned PDF-bruksanvisningen gratis på norsk. Dette produktet har for øyeblikket 0 vanlige spørsmål, 0 kommentarer og har 0 stemmer. Hvis dette ikke er bruksanvisningen du ønsker, vennligst kontakt oss.

Er ditt produkt defekt og finner du ikke løsningen i bruksanvisningen? Dra til en Repair Café for gratis hjelp til reparasjon.

Bruksanvisning

Ferm 192 Ferm

Product: Ferm Compressor

Type FC-710, Art. nr. 231710

Ferm, Genemuiden, The Netherlands

1. TECHNICAL DATA

This is a directly linked 1-cylinder compressor in mobile

design. This compressor is also equipped with a reducing

valve, a automatic shutdown and a quick coupling.

Sound pressure level 83,8 dB(A)

CAREFULLY READ THE INSTRUCTIONS

BEFORE YOU USE THE COMPRESSOR!

2. SPECIFIC SAFETY RULES

BEFORE USING THE COMPRESSOR:

1. Place the compressor in a well ventilated, frost

free area.

To obtain sufficient ventilation and cooling the distan-

ce between the shield and the wall needs to be at least

50 to 60 cm.

2. The following points need to be checked:

- do the voltage of the engine and the engine safe

guard, if any, correspond to the mains voltage (ap-

pliances for a mains voltage of 230 V can be connec-

ted to a mains voltage of 220 V without any pro-

blems);

- an earthed mains connection (wall socket) needs

to be used;

- are the mains lead and the mains plug in a good con-

dition: solid, without any loose ends or damage;

- the pressure reducing valve may not be copletely

closed so as to prevent damage to membranes;

- the oil level with help from the gauge. The oil level

should be within the area indicated by both marks

on the gauge, when the compressor is placed level.

-before use the air tank needs to be empty.

IMPORTANT: To prevent damage to the motor

windings as a result of voltage variation it is advisable

to mount an engine safety switch.

WHILE USING THE COMPRESSOR:

1. Do not use extension cables which are too long.

IMMEDIATELY SWITCH OFF THE COMPRES-

SOR IN CASE OF:

1. defective mains plug, mains line or damage to the

mains line;

2. defective switch;

3. smoke or bad smell caused by scorched insulation.

3. INSTALLATION

The compressor needs to be placed in well-ventilated,

frost-free area. To obtain sufficient ventilation and coo-

ling the distance between the shield and the wall needs to

be at least 50 to 60 cm.

4. OPERATING THE COMPRESSOR

- The mains switch needs to be in “OFF” or “0” posi-

tion before the mains plug is connected to the mains

voltage.

- Bij switching the switch to “ON” or “1” the compres-

sor will operate.

- Always keep the mains lead away from moving parts

of any linked up air-pressure equipment.

-With the use of the reducing valve it is possible to ad-

just the air pressure by hand. By pressing the reducing

valve the chosen position can be locked. However, do

not close the reducing valve too much, in order to

prevent damage to the membranes.

5. MAINTENANCE

The mains plug always needs to be taken out

of the socket (the mains socket) during main-

tenance or cleaning activities. Never use wa-

ter or other agressive liquids to clean the ma-

chine. Clean the machine by brushing it with

a brush.

PERIODIC MAINTENANCE OF THE COMPRES-

SOR WILL PREVENT UNNECESSARY PROBLEMS!

Oillevel

The compressor comes with a special test oil, that must

be Replaced after about 100 hours of use. Check the oil

level from time to time, using the oil gauge.

When the compressor is level and has not been used for

some time, the oil level should be within the area indica-

ted by both marks on the gauge. The oil must be replaced

after every 1000 hours of use. Use compressor oil API

CC SAE 40 rather than motor oil. If the compressor is

English

Art.

nr.

Type

V~/Hz W RPM LTR. L/MIN BAR

231710 FC-710 230~50 1.500 2.800 50 245 8

Exploded

FC-710

AVAILABLE SPARE PARTS FOR FC-710

REF.NR. DESCRIPTION FERM NR.

1 CYLINDER COVER (RED) 208217

2REAR COVER 208200

3 COVER 208201

6 VALVE PLATE 208252

7 FAN 208202

9 OIL LEVEL GAUGE 208203

11 CRANKSHAFT + AXLE 208204

8223091 CONNECTION ROD COMPLETE 208205

21 CONDENSOR 25 uF 800025

23 CYLINDER 208210

24 CYLINDER HEAD PACKING 208211

26 GASKET VALVE PLATE HEAD 208212

27 HEAD 208213

29 FILTER 205730

30 STATOR 208221

31 ROTOR 208222

32 CYLINDER PACKING 208216

Vurdering

La oss få vite hva du syns om FERM CRM1005 FC-710 Kompressor ved å gi en produktbedømmelse. Vil du dele dine erfaringer med dette produktet eller stille et spørsmål? Legg igjen en kommentar nederst på siden.

Er du fornøyd med FERM CRM1005 FC-710 Kompressor?
Ja Nei

Vær den første til å bedømme dette produktet

0 stemmer

Bli med i samtalen om dette produktet

Her kan du dele hva du synes om FERM CRM1005 FC-710 Kompressor. Hvis du har et spørsmål, les først bruksanvisningen nøye. Be om en bruksanvisning kan gjøres ved å bruke vårt kontaktskjema.

Mer om denne håndboken

Vi forstår at det er fint å ha en papirhåndbok for FERM CRM1005 FC-710 Kompressor. Du kan alltid laste ned bruksanvisningen fra nettsiden vår og skrive den ut selv. Hvis du vil ha en original bruksanvisning, anbefaler vi at du kontakter FERM. De kan kanskje gi en original bruksanvisning. Leter du etter bruksanvisningen til FERM CRM1005 FC-710 Kompressor på et annet språk? Velg ditt foretrukne språk på hjemmesiden vår og søk etter modellnummeret for å se om vi har det tilgjengelig.