Bruksanvisning Cocraft XAGD50 Stiftepistol

Bruksanvisning

ENGLISH

4

Compressed air feed and connections

Warning:

To prevent accidents due to unintended firing, theoperator should always disconnect

thecompressed air:

• Before adjusting

• When cleaning thenail gun

• When removing astuck nail

• When thetool is not being used

• When moving thetool to another work area

Warning:

• Use only compressed air in pneumatically driven tools. Never use acid or flammable gases to

drive thetool since they carry therisk of explosion.

• Thecompressor capacity must be sufficient to ensure anadequate air pressure and flow for

theintended use. Afall in pressure in thesystem can reduce thetool’s thrust. See Specifications

for setting theright pressure for thetool.

• Thecompressed air lines should be mounted on anincline, with thehighest point closest to

thecompressor. Aneasily accessed water separator should be installed at thelowest points.

Thewater separator should be emptied at least once aday, or more often if needed. Dirt and

water in thecompressed air lines are one of many causes of wear in pneumatically actuate tools.

• Thetool connection fittings should be equipped with areducing valve with water separator

directly at theconnection site. Afilter helps to achieve maximum effect at minimum wear.

Thefilter must have sufficient flow capacity for theintended mounting site or connecting point.

Thefilter must be kept clean if it is to be able to deliver clean compressed air to thetool. See

themanufacturer‘s instructions for proper filter care. Adirty or clogged filter will cause afall in

pressure, which reduces thenail gun’s effectiveness.

• Thepressure regulator must be adjustable from 0 to 7 bar.

• Theair hoses must tolerate at least 10.5 bar working pressure or 150% of themaximum

air pressure thesystem can create. Themeter line should have aquick coupling for quick

detachment from thenail gun’s nipple.

• Make sure that thecompressed air fed to thenail gun does not exceed themaximal

permissible working pressure (7 bar). Initially set themeter pressure at thelowest

recommended working pressure; See Specifications.

• Check that thenail gun is working properly by running function and safety checks for every job.

Warning:

To prevent serious eye injury from flying nails and/or slivers, theoperator and others in

theworking area must be equipped with eye protection that covers both thefront and thesides

when loading, using or servicing thetool.

Glasses without eye protection on theside and facemasks do not give adequate protection.

Vurdering

Mer om denne håndboken

Vi forstår at det er fint å ha en papirhåndbok for Cocraft XAGD50 Stiftepistol. Du kan alltid laste ned bruksanvisningen fra nettsiden vår og skrive den ut selv. Hvis du vil ha en original bruksanvisning, anbefaler vi at du kontakter Cocraft. De kan kanskje gi en original bruksanvisning. Leter du etter bruksanvisningen til Cocraft XAGD50 Stiftepistol på et annet språk? Velg ditt foretrukne språk på hjemmesiden vår og søk etter modellnummeret for å se om vi har det tilgjengelig.

Spesifikasjoner

Alle bruksanvisninger for Cocraft Stiftepistoler
Flere håndbøker for Stiftepistoler

Ofte stilte spørsmål om Cocraft XAGD50 Stiftepistol

Vårt supportteam søker etter nyttig produktinformasjon samt svar på ofte stilte spørsmål. Hvis du finner en feil i våre ofte stilte spørsmål, vennligst gi oss beskjed ved å benytte vårt kontaktskjema.

Relaterte produkter

Bruksanvisning

Cocraft XAGD50/9040 Stiftepistol

Bruksanvisning

Ryobi R18ST50-0 Stiftepistol

Bruksanvisning

Rapid ESN114 Stiftepistol

Bruksanvisning

Meec Tools 071-015 Stiftepistol

Bruksanvisning

Makita AF505 Stiftepistol

Bruksanvisning

Bosch PTK 3,6 LI Stiftepistol

Bruksanvisning

Makita AN453 Stiftepistol

Bruksanvisning

Black and Decker BDCT12 Stiftepistol

Relaterte kategorier