Bruksanvisning Black and Decker EPL18 Drill-skrutrekker

Bruksanvisning

6

ENGLISH

(Original instructions)

tool. Slide the battery into the receptacle and push until

the battery snaps into place.

u To remove the battery, push the release button (9) while at

the same time pulling the battery out of the receptacle.

Fitting and removing a drill bit or screwdriver bit

(g. D)

This tool is tted with a keyless chuck to allow for an easy

exchange of bits.

u Grasp the rear half of the chuck (3) with one hand and use

your other hand to rotate the front half in the

counterclockwise direction, as viewed from the chuck end.

u Insert the bit shaft (10) into the chuck.

u Firmly tighten the chuck by holding the rear half of the

chuck and rotating the front portion in the clockwise

direction as viewed from the chuck end.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

u To charge the battery (5), insert it into the charger (7). The

battery will only t into the charger in one way. Do not

force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (8) will ash green continuously

(slowly).

The charge is complete when the charging indicator (8) lights

green continuously. The charger and the battery can be left

connected indenitely with the LED illuminated. The LED will

change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging

indicator (8) will be lit as long as the battery is connected to

the plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (8) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (5).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Selecting the direction of rotation (g. E)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the torque

This tool is tted with a collar to set the torque for various

screwdriving and drilling applications. Large screws and hard

workpiece materials require a higher torque setting than small

screws and soft workpiece materials. For the denition of the

symbol refer to the listing below.

u For drilling in wood, metal and plastics, set the torque

adjustment collar (4) to the

b

symbol.

u For screwdriving, set the collar to the desired setting. If

you do not yet know the appropriate setting, proceed as

follows:

- Set the torque adjustment collar (4) to the lowest torque

setting.

- Tighten the rst screw.

Vurdering

Mer om denne håndboken

Vi forstår at det er fint å ha en papirhåndbok for Black and Decker EPL18 Drill-skrutrekker. Du kan alltid laste ned bruksanvisningen fra nettsiden vår og skrive den ut selv. Hvis du vil ha en original bruksanvisning, anbefaler vi at du kontakter Black and Decker. De kan kanskje gi en original bruksanvisning. Leter du etter bruksanvisningen til Black and Decker EPL18 Drill-skrutrekker på et annet språk? Velg ditt foretrukne språk på hjemmesiden vår og søk etter modellnummeret for å se om vi har det tilgjengelig.

Spesifikasjoner

Alle bruksanvisninger for Black and Decker Drill-skrutrekkere
Flere håndbøker for Drill-skrutrekkere

Ofte stilte spørsmål om Black and Decker EPL18 Drill-skrutrekker

Vårt supportteam søker etter nyttig produktinformasjon samt svar på ofte stilte spørsmål. Hvis du finner en feil i våre ofte stilte spørsmål, vennligst gi oss beskjed ved å benytte vårt kontaktskjema.

Relaterte produkter

Bruksanvisning

Black and Decker ASL186 Drill-skrutrekker

Bruksanvisning

Black and Decker KC14XC Drill-skrutrekker

Bruksanvisning

Black and Decker KR2000K Drill-skrutrekker

Bruksanvisning

Black and Decker HP186F4BK Drill-skrutrekker

Bruksanvisning

Black and Decker HP14KD Drill-skrutrekker

Bruksanvisning

Black and Decker PS142/H Drill-skrutrekker

Bruksanvisning

Black and Decker MT188 Drill-skrutrekker

Bruksanvisning

Black and Decker BCD700S Drill-skrutrekker

Relaterte kategorier