Bruksanvisning Bionaire BEF6500 Elektrisk peis

Bruksanvisning

selected temperature level by automatically

turning the heater ON and OFF.

3. If the heater cycles ON/OFF frequently

select a higher preset temperature.

4. To switch the digital thermostat mode off,

press the digital thermostat button until the

LEDs on digital thermostat setting on the

control panel or remote are no longer lit.

CLEANING/MAINTENANCE

TIMER

Note: Timer will work only if one of the three

mode settings is used.

1. Press the digital timer button (L) on the

control panel or remote enough times to

activate one of the 6 preset desired OFF

times (2,4,6,8,10 or 12 Hrs)

2. The timer will now turn the unit completely

off based on the selected OFF time.

3. To switch the digital timer mode off, press

the digital timer button until the LEDs on

timer setting on the control panel or remote

are no longer lit.

FLAME INTENSITY

There are five flame brightness settings, ranging

from a low to high setting and then OFF. Press

flame intensity button (M) on the control panel

or remote control to select desired intensity.

Please note that this function works on all

modes and is also fully independent.

AUTO SAFETY SHUT OFF

This heater is equipped with a technologically

advanced safety system that automatically shuts

off the current to the heater when a potential

overheat temperature is reached. The heater

can resume operation only when you reset it

and after it has cooled down.

RESET INSTRUCTIONS

If the unit shuts down:

1. Turn main unit ON/OFF SWITCH to position

( ) (see Fig. 2, N)

2. Unplug unit, wait 30 minutes

3. Plug in the unit

4. Turn main unit ON/OFF SWITCH to position

(–) (see Fig. 2, N)

5. Select desired mode and setting following

operating instructions.

BULB REPLACEMENT

1. Turn off and unplug the unit from the power

socket.

2. Leave the unit to stand for 5 minutes so that

the bulb can cool down.

3. Remove the front glass panel to a safe place.

4. Empty the pebbles from the unit.

5. Unscrew the light bulb access panel (C)

using a cross head screwdriver, being

careful not to lose the screws.

6. Pull out the bulb.

7. Replace the G9 Type bulb with the same

type with a 40W max rating.

8. Screw back the light access panel, replace

the pebbles and front glass and plug the unit

into the power socket for operation.

Note: The G9 Type bulb should be readily

available from most hardware stores. If not please

contact the manufacturer for further assistance.

CLEANING AND MAINTENANCE

• Always unplug the heater before cleaning and

allow to cool.

• To clean glass use household glass cleaner.

• Lightly run a vacuum cleaner nozzle over the

heater vent to remove any dust or dirt that

may have accumulated.

• Carefully wipe the heater with a soft, damp

cloth. Please be very cautious near the

heating elements.

* NEVER use abrasive or flammable solvents

to clean the heater.

• After cleaning, be sure to completely dry the

heater with a cloth or towel before switching on.

• Store your heater in a cool, dry location.

TROUBLESHOOTING

Flame not bright enough

1. Regulate flame brightness using the flame

intensity button.

2. Check bulb is working and replace if

necessary.

Simulated fire will not illuminate

1. Check power.

2. Press the flame intensity button.

3. Check bulb and replace if necessary.

Unit making crackling/popping sound

1. This is normal; when the unit is first used or

has not been used for a while this sound is

caused by dust buildup burning away.

2. Please refer to Cleaning and Maintenance

section for prevention.

Heater will not turn off

1. Refer to operating instructions.

Heater blows cool air

1. This is normal when the unit is on the fan

only setting.

2. Press the mode control (K) until you select

the LOW (1) or HIGH (2) heat setting.

mechanical ON/OFF switch (N). Please note this

remote will not work through walls (See Fig. 3).

Stand Assembly (See Fig. 6):

For floor use attach the two feet assemblies (I) to

the fireplace heater using the 4 thumb screws (O)

provided. Gently lay the main housing (D) down

horizontally without the glass panel attached. Line

up each feet assembly using the metal guides

and then screw in two thumb screws (O) into the

corresponding holes. Place unit upright, add the

pebbles (B) and then attach the glass panel by

lining up the glass panel metal guides with the

main housing panel pins. For wall mounting see

Wall Mount Installation below.

Wall Mount Installation (See Fig. 4 & 5):

This product weighs 16.3 kg. Do not install

alone. The following procedure is for a dry wall

installation using the provided hardware.

Note: If installing on a different type of wall (i.e

cavity wall) or using different hardware please

consult a professional for advice on the correct

way to install the unit.

IMPORTANT: Before drilling into any wall

ensure no electrical cables are present in the

area. Make sure you allow at least 1m of

space on all four sides of unit.

1. Turn unit off and disconnect the unit if in use.

2. Remove front glass and pebbles if installed.

3. Remove feet assemblies from main housing

by unscrewing the thumb screws.

4. Decide on the position where the electric

fireplace will hang on the wall. REMEMBER

not to position directly above the power

socket and at least 1m away from any objects

on all sides (reference Fig. 5).

5. Mark on the wall the points between the

centre of the holes on the fixed unit rear

mounting brackets (E) making sure the points

line up and are level (reference Fig. 4)

6. Drill into the wall using an 8mm drill bit two

holes on the marked points so that you can fit

the appropriate wall plugs.

7.

Screw in two 4 x 35mm screws into the wall plugs,

leaving 10mm of the screws out of the wall.

8. Hang the main body of the unit onto the two

exposed screws by lining up the rear

mounting brackets’ holes.

9. Place the securing bottom bracket (P) into the

rear of the unit and then use one 4x35mm

screw to secure the bracket and unit to the

main wall.

10. Add pebbles to the unit, then place the glass

panel onto the unit by lining up the glass

panel guides with the main housing pins

(located on the side of the housing) and make

sure the unit is secure.

11. Unit is now ready to be turned on and

operated.

OPERATING INSTRUCTIONS

• There may be an odor coming from the

heater the first time you use it. This is

normal during the break-in period or after

long term storage. Make sure the heater is in

a well ventilated area and continue running it

until the smell goes away.

• You may hear a popping or crackling sound

as the heater heats up. This is normal and

safe operation.

• The Fireplace Heater can be operated by

using the remote control (Fig. 3) or the

control panel (Fig. 2) located on the side of

the unit.

• Place the heater on a firm, level surface or

mount on wall.

• Avoid overloading your circuit by not using

other high wattage

POWER ON/OFF

1. Turn the main ON/OFF switch (N) on the

main unit to the ON (–) position.

2. Either press the mode control (K) or the

flame intensity button (M) on the main unit

or remote control to start the operation of

the unit.

3. If for any reason you would like to turn the

unit off press the mode button or flame

intensity button on the the ON/Off Button (Q)

on the control panel or remote so that no

function is heard or visible and then switch

the ON/OFF switch on the main unit to the

OFF ( ) postion.

MODE SETTINGS

Once the main ON/OFF switch has been

switched to ON, press the mode control button

(K) on the panel or remote control:

for Fan only setting

1= for continuous low heat (1kW)

2= for continuous high heat (2kW)

Press again for no mode operation.

THERMOSTAT

Note: Thermostat will operate only if the unit is

on the Low (1) or High (2) heat setting.

1. Press the digital thermostat button (J) on the

control panel or remote enough times to

activate one of the 5 preset

desiredtemperature levels (18ºC, 21ºC,

24ºC, 27ºCº and 30ºC). An LED on the unit

or the remote control will illuminate to show

the selected setting.

2. The thermostat will now maintain the

6 7

Vurdering

Mer om denne håndboken

Vi forstår at det er fint å ha en papirhåndbok for Bionaire BEF6500 Elektrisk peis. Du kan alltid laste ned bruksanvisningen fra nettsiden vår og skrive den ut selv. Hvis du vil ha en original bruksanvisning, anbefaler vi at du kontakter Bionaire. De kan kanskje gi en original bruksanvisning. Leter du etter bruksanvisningen til Bionaire BEF6500 Elektrisk peis på et annet språk? Velg ditt foretrukne språk på hjemmesiden vår og søk etter modellnummeret for å se om vi har det tilgjengelig.

Spesifikasjoner

Alle bruksanvisninger for Bionaire Elektriske peiser
Flere håndbøker for Elektriske peiser

Relaterte produkter

Bruksanvisning

Anslut 017-392 Elektrisk peis

Bruksanvisning

Rusta Bergen Elektrisk peis

Bruksanvisning

Point POWF26 Elektrisk peis

Bruksanvisning

Emerio FP-121933 Elektrisk peis

Bruksanvisning

Point POWF42 Elektrisk peis

Bruksanvisning

Qlima EFE2018 Elektrisk peis

Bruksanvisning

Cotech ND-183-D Elektrisk peis

Bruksanvisning

Voltomat EF330L Elektrisk peis

Relaterte kategorier