Bruksanvisning Bionaire BASF1415 Vifte

Bruksanvisning

32

Final assembly

1. Slide the inner pole extension (K) up from

the outer pole (M). Insert the pole locking

knob (L) into the hole on the outer pole, to

securely hold this position.

2. Place the fan head assembly into this

extension pole, inserting the neck of the fan

into the pole opening. Turn the fan head's

neck until the head is securely locked into

place.

3. Add the tilt adjustment knob (J) to the hole in

the fan head's neck (I). Tighten when the fan

head is in your desired position.

Converting to a table fan -

On model BASF1415 an additional short pole

(Q) is supplied which allows the fan to be

converted into a table fan. To change to this

short pole, remove the fan head assembly from

its position on top of the inner pole and unscrew

the L-shaped locking lever at the base. Remove

the long pole, replace with the short pole and

reassemble as detailed above.

OPERATING INSTRUCTIONS

1. Set the fan base on a dry level surface

2. Make sure the Selector (Speed) Control (S)

is in the OFF (0) position. Selector (Speed)

Control (S) is located on the top of the fan

motor housing.

3. Plug the cord into a suitable 220-240V. AC

outlet.

4. The SPEED is adjusted by turning the

Selector (Speed) Control (S) to the desired

setting:-

0-III-II-I.

5. The OSCILLATION control (T) is located on

the top of the fan motor housing. To start

oscillation, push the control knob down.

To stop oscillation, pull the control knob up.

ADJUSTMENT

Tilt adjustment

Follow these instructions to tilt the fan head for

upward angle air movement.

1. To change the tilting angle of the fan head,

simply loosen the tilt adjustment knob (J)

2. Move the fan head to the desired angle, then

firmly tighten the knob to lock in place.

Height adjustment

Follow these instructions to adjust the height of

the fan.

1. Turn the pole locking knob (L) anti-clockwise

to loosen the pole.

2. Adjust the pole to the desired height and

firmly tighten the locking knob in a clockwise

direction.

CLEANING AND MAINTENANCE

Follow these instructions to correctly and safely

care for your Bionaire

TM

fan. Please remember:-

• Always unplug the fan before cleaning or

assembly.

• Do not allow water to drip on or into the fan

motor housing.

• Be sure to use a soft cloth, moistened with a

mild soap solution.

• Do not use any of the following as a cleaner:

petrol, thinners or benzene.

Fan Blade cleaning

(See instructions for fan head assembly)

1. To access the fan blade, remove the front

grill and securing screw.

2. Clean the fan blade, front and rear grills with

a soft moist cloth.

3. Replace the fan blade, tighten screw and

securely fasten the front grill.

Fan head, base and pole cleaning

Using a soft, moist cloth, with or without a mild

soap solution, carefully clean the fan base, pole

and head. Please use caution around the motor

housing area. Do not allow the motor or other

electrical components to be exposed to water.

FAN STORAGE

Your fan can be stored either partially

disassembled or assembled.

It is important to keep it in a safe, dry location.

• If stored disassembled, we recommend using

the original (or appropriately sized) box.

• If stored assembled or partially assembled,

remember to protect the fan head from dust.

For U.K. and Ireland only:

If the plug is not suitable for the socket outlets in

your home, it can be removed and replaced by

a plug of the correct type. Please refer to

"Installation of a plug" below.

Installation of a plug Applicable to

U.K. and Ireland

NOTE: If the terminals in the plug are not

marked or if you are unsure or in doubt about

the installation of the plug please contact a

qualified electrician.

PLEASE READ AND SAVE THESE

INSTRUCTIONS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including

the following:-

• Use the fan only for purposes described in

the instruction manual.

• To protect against electrical shock, do not

immerse the fan, plug or cord in water or

spray with liquids.

• Close supervision is necessary when any

appliance is used by or near children.

• Unplug from the electrical outlet when not in

use, when moving the fan from one location

to another, before putting on or taking off

parts and before cleaning.

• Avoid contact with any moving parts.

• Do not operate in the presence of explosive

and/or flammable fumes.

• Do not operate fan until fully assembled with

all parts properly in place.

• To avoid fire hazard, NEVER place the cord

under rugs or any parts near an open flame,

cooking or other heating appliance.

• Ensure that the fan is switched off from the

supply mains before removing the guard.

• Do not operate any appliance with a

damaged cord, plug, after the appliance

malfunctions, or has been dropped/damaged

in any manner.

• The use of attachments not recommended or

sold by the appliance manufacturer may

cause hazards.

• Do not use outdoors.

• Do not let the cord hang over the edge of a

table or counter, or come into contact with

hot surfaces.

• To disconnect from the electrical supply, grip

the plug and pull from the wall outlet. DO

NOT pull on the cord.

• Always use on a dry, level surface.

• Do not operate without the fan grills properly

in place.

• This product is intended for household use

ONLY and not for commercial or industrial

applications.

• If the supply cord or plug is damaged, it must

be replaced by the manufacturer or its

service agent or a similarly qualified person

in order to avoid hazard.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure that

they do not play with the appliance.

MISSING A PART FOR YOUR FAN?

Please call 0800 052 3615 for assistance.

ASSEMBLY INSTRUCTIONS (See Fig 1.)

Base/Pole assembly

You will need the base cover (N), weight (O),

pole (K,M), washer (R) and L-shaped locking

lever (P).

1. Turn the base cover upside down and place

the weight into the base cover.

2. Insert the threaded end of the L-shaped

locking lever into the hole of the washer,

weight and through the base cover.

3. Whilst holding the base cover and weight with

one hand, connect the pole to the base,

sliding the L-shaped locking lever into the

bottom of the pole (M) with your other hand.

4. Turn the L-shaped locking lever clockwise to

securely attach the pole to the base.

5. Set the base on the floor, weight side down.

Fan head assembly

You are now ready to assemble the fan head.

1. Unscrew rear grill mounting nut (D) before

positioning the rear grill (F) over the motor

shaft (G) making certain that the notches at

the top and bottom of the rear grill, fit over

the prongs on the motor housing (H).

2. Secure the rear grill in its place using the

rear grill mounting nut (D). Turn this nut

clockwise and tighten firmly.

3. Slide the fan blade (B) with the hollowed

interior of the blade facing toward the rear

grill, firmly onto the motor shaft. The top of

the motor shaft should lie even with the

centre of the fan blade.

4. Now use the securing screw (C) (already

attached to the Fan Blade) to lock the blade

into place. Tighten the screw into the side

hole of the fan blade, against the motor

shaft, until both the blade and screw are

secure.

5. Centre the front grill (A) by aligning the

Bionaire logo on the logo plate so that it is

horizontal and parallel with the floor. Then,

holding the front grill against the rear grill,

push the black grill ring (E) into place at the

top and bottom of the fan. (Push directly on

the black grill ring, not on the grills

themselves). Finish securing the grill ring in

the same manner until both grills are joined

underneath the black ring.

BASF1415 Fig. 1

A

B

I

C

Q

D

E

F

G H

J

K

L

M

N

O

P

R

T

S

ENGLISH

BASF1415-I_09MLM1.indd 4-6BASF1415-I_09MLM1.indd 4-6 6/18/09 11:00:08 AM6/18/09 11:00:08 AM

Vurdering

Mer om denne håndboken

Vi forstår at det er fint å ha en papirhåndbok for Bionaire BASF1415 Vifte. Du kan alltid laste ned bruksanvisningen fra nettsiden vår og skrive den ut selv. Hvis du vil ha en original bruksanvisning, anbefaler vi at du kontakter Bionaire. De kan kanskje gi en original bruksanvisning. Leter du etter bruksanvisningen til Bionaire BASF1415 Vifte på et annet språk? Velg ditt foretrukne språk på hjemmesiden vår og søk etter modellnummeret for å se om vi har det tilgjengelig.

Spesifikasjoner

Alle bruksanvisninger for Bionaire Vifter
Flere håndbøker for Vifter

Ofte stilte spørsmål om Bionaire BASF1415 Vifte

Vårt supportteam søker etter nyttig produktinformasjon samt svar på ofte stilte spørsmål. Hvis du finner en feil i våre ofte stilte spørsmål, vennligst gi oss beskjed ved å benytte vårt kontaktskjema.